Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
Right here in the next paragraph you can locate a good deal of incredibly good advice related to Tools You Need to Install a New Bathtub .
Mounting a tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is easily easily accessible, the project can move easily; if you need to open a wall surface to get rid of the old bathtub and place the new bathtub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly need a helper to leave the old tub and also set in the brand-new one. Make certain you have certified on your own for the job and fit trying it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will certainly aid you mount a new tub in your shower room if you have actually currently bought a brand-new bathtub and do not require to alter the setup of your previous water supply pipes.
Your devices as well as material list need to comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be quite bothersome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. When the supply pipes have been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to moving on to fit the new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines remain in location in between the tap as well as the sink. Secure the tap in place with the producer given backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former type ought to be linked to the faucet ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Making use of the two wood boards under its feet, position the tub in the called for setting. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub till the level reviews degree.
To set up faucets, fit the bottom of the furthest flexible tap port to the appropriate supply pipe by making a compression join; then do the same for the various other tap.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has been made use of a minimum of once as this will resolve it into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom must be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split an inflexible seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, bring about issues with dampness and also feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealer can break fairly very early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt about Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to read through our content. Make sure you take the opportunity to promote this blog posting if you enjoyed reading it. Thanks a lot for your time spent reading it.
Contact our experts. Report this page